当前位置:网站首页>Beijialai touch screen maintenance 4pp065 0571-X74F
Beijialai touch screen maintenance 4pp065 0571-X74F
2022-04-23 22:03:00 【A Tiandao reward Service ~ Tianpu Zhengda maintenance Cao Gong】
The maintenance faults of baccalais touch screen include : Do not start 、 Black screen 、 Blue screen 、 The LCD screen is damaged 、 Motherboard burned out 、 Touch failure 、 The statement 、 The card machine 、 The image has interference marks 、 Burning element 、 Image jitter 、 No response to the key 、 Power board failure 、 No backlight 、 Restart again and again 、 Individual areas cannot be touched 、 Touch offset 、 High voltage board failure, etc .
No response processing method of touch screen : Check whether each wiring interface is loose , Then check whether the serial port and stop number conflict , If there is any conflict , Resources should be adjusted , Avoid conflict . Then check whether there are cracks on the surface of the contact screen , If there is any crack, it shall be replaced in time . It is also necessary to check whether there is dirt on the surface of the contact screen , If you have any , Remove with a soft cloth . Investigate and check whether the indicator light on the control box works normally , Normal , The light is green , And shine .
After power on, the screen does not display the correction process : Touch the screen with your hand , The buzzer doesn't respond , Clarify that the program is not working properly . Measure several groups of voltages with a multimeter 3.3 v 、5.1 v 、12 The voltage is normal . According to the user , After the user found the fault of the contact screen, he tried to repair , During power on , There was a normal situation , But it won't work if you turn it on again after power failure . Analysis of faulty soldering at a pin of the chip , Make the bus fault , Then the program can't run . Then the hot-air gun is used to heat the welding leg of the dense foot chip , At the same time, press the chip with tweezers , Make the welding leg and tin fuse from the beginning .
How to deal with the non reaction of touch screen after use : Some applications , Due to poor grounding function , Because the shell of the control box is covered with a lot of static electricity , Then affect the operation electric field inside the control box , Cause the contact to fail gradually . At this time, use a wire to ground the control box shell , Just start from scratch .
In case of capacitive touch screen, the screen calibration program can be run under the following conditions :
1. Complete the installation of driver software at one time . The second is to try to change the resolution or display mode of the display every time ,
2. The next step is to change the display area every time .
3. Then try to adjust the frequency of the controller every time , Check that the cursor and touch point cannot correspond each time .
4. After calibration , The calibrated data is stored in the register of the controller , This eliminates the need to calibrate the screen every time the system is started .
During the maintenance of Baccarat touch screen, it is recommended to check whether each wiring interface is loose , Then check whether the serial port and interrupt number conflict , In case of conflict , Resources should be adjusted , Avoid conflict . Then check whether there are cracks on the surface of the touch screen , If there is any crack, it shall be replaced in time . It is also necessary to check whether there is dust on the surface of the touch screen , If you have any . Observe and check whether the indicator light on the control box works normally , Normal , The light is green , And flashing . The maintenance of Beijialai touch screen is a complicated process , And it will involve the problems of various components , This is for the operator , The key is whether you can find the problem .
版权声明
本文为[A Tiandao reward Service ~ Tianpu Zhengda maintenance Cao Gong]所创,转载请带上原文链接,感谢
https://yzsam.com/2022/04/202204200607459980.html
边栏推荐
- DW basic course (II)
- Pycharm download and installation
- 轻量化项目管理思路
- consul client客户端开发
- Display, move, rotate
- Hystrix组件
- [leetcode sword finger offer 58 - I. flip word order (simple)]
- Database Experiment 5 Security Language Experiment
- Resolve the "chromedriver executable needs to be in path" error
- How to use the project that created SVN for the first time
猜你喜欢
[※ leetcode refers to offer 46. Translate numbers into strings (medium)]
服务注册中心和Ribbon组件回顾
延时消息常见实现方案
服务雪崩效应
Code cloud download history version process
openfeign集成Hystrix的备选方案处理
C winfrom DataGridView click on the column header can not automatically sort the problem
[leetcode refers to offer 18. Delete the node of the linked list (simple)]
轻量化项目管理思路
Database Experiment 2 data query
随机推荐
consul server 服务注册中心安装
OpenFeign超时设置
Pyuninstaller package exe cannot find the source code when running, function error oserror: could not get source code
DW basic course (II)
Database Experiment 7 stored procedure experiment
[leetcode refers to the two numbers of offer 57. And S (simple)]
Subcontracting of wechat applet based on uni app
How Axure installs a catalog
[leetcode sword finger offer 58 - I. flip word order (simple)]
构造函数 & 析构函数
在线Excel转CSV工具
LabVIEW修改应用程序窗口外观
上海确保疫情保供生活物资质量和食品安全
服务雪崩、服务熔断、服务降级
清华大学 | WebFace260M:百万级深度人脸识别的基准(TPAMI2022)
分布式系统服务熔断
[※ leetcode refers to offer 48. The longest substring without repeated characters (medium)]
[leetcode refers to offer 32 - III. print binary tree III from top to bottom (medium)]
Common scenes of vector product in image
LabVIEW设置应用程序显示标签透明